Showing results: 31 - 40 of 40 items found.
-
CXM Series -
Cytec Corp.
This series is typically used for frequencies from DC to 40 GMHz. We use microwave relays, splitters, programmable attenuators and many other microwave components from the worlds most popular vendors to build standard or custom systems to your specifications. There are a large variety of 1x2 through 1x12 microwave relays available in Normally Open, Failsafe, Latching, Terminated or special configurations to suit your needs. Or simply buy the driver chassis and use it to control your own components. Since Cytec doesn"t build microwave components we can put the systems together with whatever parts you prefer and stand behind the warranty for you.
-
Teledyne RF & Microwave
Microwave Solutions is a worldwide leader in the design, development, and manufacture of RF and microwave components. Our broad line of components operate in the 100 kHz to 26GHz range and include Attenuators, BAW Devices, Detectors, Isolators and Circulators, Linearizers, Mixers, and VCOs. For over 50 years our components have played key roles in sophisticated airborne and satellite communications equipment, navigation and guidance systems, radar and sonar equipment, telemetry electronics, surveillance, and reconnaissance systems, and high performance commercial test equipment.
-
Keysight Technologies
The Keysight RF and Microwave multiplexer modules for the 34980A Multifunction Switch/Measure Unit offer broadband switching capabilities for switching from DC to 26.5 GHz. Use these modules to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. A switch/attenuator driver module also allows control of switches and attenuators external to the 34980A Mainframe.
-
FSMR3000 -
Rohde & Schwarz GmbH & Co. KG
The R&S®FSMR3000 is a microwave measurement receiver to calibrate signal generators and attenuators with one single instrument. Most important features provided are tuned RF level measurements, level measurements, analog modulation and spectrum analysis. Additionally, the R&S®FSMR3000 can be equipped with powerful hardware for high-end phase noise test supplementary to the standard phase noise test with the spectrum analyzer.
-
Microsemi Corporation
Microsemi's portfolio of MMIC products targets a broad range of applications including those in electronic warfare, radars, instrumentation (test and measurement) and microwave communications. The portfolio comprises broadband amplifiers (both power and low-noise), amplifier modules, prescalers, attenuators and switches spanning DC to 65GHz based on high-performance process technologies. Microsemi offers 18 distributed amplifier products including industry-leading DC-65GHz MMICs. Microsemi's prescalers combine higher frequency operation, the flexibility to divide by a large number of ratios and very good residual phase noise.
-
QPA8, PA8 -
GigaBaudics Co.
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA8 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly. Attenuation is controlled in standard steps of 0.0625 dB. The 10 bit programmable range results in the full 210=1024 steps yielding a dynamic range of 0 to 63.9375dB. Non-standard custom step sizes are available.
-
Acery Technologies
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
LDA-906V Lab Brick® -
Vaunix Technology Corporation
The Lab Brick LDA series of Digital Attenuators bring affordability, functionality, reliability and simplicity to the microwave test bench. The LDA products range from 6 MHz to 20 GHz with input level tolerance to 2 Watts and step size as small as 0.1 dB. Lab Bricks use a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems.
-
SA1001H -
Hangzhou Softel Optic Co., Ltd.
*SA1001H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network.. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network*It is more convenient for debug engineering debug, because of the plug-in diplexer filters with built-in adjustable equalizers, adjustable attenuators, plug-in output splitters and scientific and reasonable ports for online test.*These equipments will work in the field rugged environment for a long time continuously, because of the aluminium alloy casing, good heat dispersing performances, beautiful looks, dependable linear power supply and lightning protection systems.
-
S95090B -
Keysight Technologies
The S95090B spectrum analyzer (SA) measurement software adds high-performance microwave spectrum analysis to PXI VNAs. With fast stepped-FFT sweeps resulting from optimized data processing, the SA software application provides quick spurious searches over broad frequency ranges. The S95090B software uses the PXI network analyzer's test and reference receivers to complete simultaneous spectrum measurements. Multi-channel SA measurements leverage the PXI VNA's internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The S95090B spectrum analyzer software application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy. Optional external attenuators should be connected with the VNA’s test ports to avoid receiver compression when measuring large signals.
